Construction Chemicals

Product Details:

2 GP Fosroc Conbextra  is supplied as a ready to use dry powder. The addition of a controlled amount of clean water produces a free flowing, non-shrink grout for gap thicknesses up to 100 mm.

Uses:

• Conbextra GP2 is used for precision grouting where it is essential to withstand static and dynamic loads. Typical applications would be the grouting of base plates of turbines, compressors, boiler feed pumps etc., It can also be used for anchoring a wide range of fixings. These include masts, anchor bolts and fence posts. 

Advantages:

• Gaseous expansion system compensates for shrinkage and settlement in the plastic state.
• No metallic iron content to cause staining.
• Pre-packed material overcomes onsite batching variations.
• Develops high early strength without the use of chlorides.
• High ultimate strength ensure the durability of the hardened grout.
• Free flow ensures high level of contact with load bearing area

Description:

• Conbextra GP2 is supplied as a ready to use dry powder. The addition of a controlled amount of clean water produces a free flowing, non-shrink grout for gap thicknesses up to 100mm.
• Conbextra GP2 is a blend of Portland cement, graded fillers and chemical additives which impart controlled expansion in the plastic state whilst minimising water demand. The low water demand ensures high early strength. The graded fillers are designed to assist uniform mixing and produce a consistent grout.

Technical support:

• An experienced technical advisory team is available to give technical service on request.

Specification Clauses:

• Performance specification All grouting shown on the drawing must be carried out with a pre packed cement based product which is chloride free. It shall be mixed with clean water to the required consistency. The grout must not bleed or segregate. A positive volumetric expansion shall occur while the grout is plastic by means of gaseous system.

Typical detail of stanchion base plate:

• The compressive strength of the grout must exceed 50 N/mm2 at 7 days and 60 N/mm2 at 28 days.
• The flexural strength of grout must exceed 9N/mm2 @ 28 days. The fresh wet density of the mixed grout must exceed 2150 kg/ m3.
• The storage, handling and placement of the grout must be in strict accordance with the manufacturer's instructions. 

Application instructions:

• Preparation Foundation Surface: The substrate surface must be free from oil, grease or any loosely adherent material. If the concrete surface is defective or has laitence, it must be cut back to a sound base. Bolt holes and fixing pockets must be blown clean of any dirt or debris.
• Pre-soaking Several hours prior to placing, the concrete substrates should be saturated with fresh water.
• Immediately before grouting takes place any free water should be removed with particular care being taken to blow out all bolt holes and pockets.
• Base Plate: It is essential that this is clean and free from oil, grease or scale. Air pressure relief holes should be provided to allow venting of any isolated high spots.
• Levelling Shims: If these are to be removed after the grout has hardened, they should be treated with a thin layer of grease.
• Formwork: The formwork should be constructed to be leakproof. This can be achieved by using foam rubber strip or mastic sealant beneath the constructed formwork and between joints.
• In some cases it is practical to use a sacrificial semi-dry sand and cement formwork. The formwork should include outlets for pre-soaking.

Product Details:

Matching up with the requirements of our clients, we are involved in offering AR Standard Nitobond Chemical

Uses:

• For improving and bonding floor toppings, mortars and renders
• As a bonding agent for Renderoc and other cementitious mortars
• Polymer modified mortars and screeds for reinstatement of worn out/damaged concrete
• Polymer modified concrete for improving the impermeability and there by enhancing the waterproofing property

Advantages:

• Good Adhesion: Provides good bond to concrete, masonry, stone work, plaster and block work.
• Increased Strength: Improves tensile and flexural properties of mortar.
• Versatile: Compatible with all common hydraulic cements
• User Friendly: application by brush/spray
• Improves Cohesion: No bleeding and segregation.

Description:

• Nitobond AR Std. is a single component latex acyrlic polymer emulsion used as bonding aid cum cement modifier with waterproofing property. 

Technical Support:

• Fosroc offers technical support service to specifiers, end users and contractors, as well as on-site technical assistance in locations all over the country

Mix proportions:

• As a cement modifier: 1 litre Nitobond AR Std. : 5 kg cement : 15 kgs graded quartz sand.
• As a bonding agent: 0.5 part cement : 1 part Nitobond AR Std. by weight.
• As waterproofing agent: 2-5% of Nitobond AR Std. shall be mixed with concrete by weight of cement. 

Application instructions:

• Surface Preparation: The object of the surface preparation is to achieve a clean sound surface with a good mechanical key. All substrates should be cleaned and free of dust, plaster, oil, paint, grease, corrosion deposits, and any other deleterious substances. Laitence should be removed by mechanical means. Oil or greasy deposits should be removed by suitable means. All surfaces so treated should be thoroughly washed with clean water. Smooth substrates must be mechanically roughened e.g. by scabbling, needle gun or grit/ sand blasting to provide a mechanical key.
• Concrete repairs: Any reinforcing steel in the repair area should be exposed around its full circumference and cleaned to remove all loose scale and corrosion deposits and then primed with Nitocote AP35, acrylic primer. All surface dust and debris shall be removed.
• Priming: Immediately before priming, the concrete substrate should be thoroughly dampened with water and any excess being brushed off. Scrub Nitobond AR Std. bonding aid into the substrate. Puddling of the emulsion to be avoided. The repair mortar/topping should be applied whilst the primer is still tacky. However a satisfactory bond can be achieved upto 15 mins. after application at 300 C.
• In order to obtain a smooth consistency mortar, the cement and sand must be dry mixed and then poured into the liquid with the required amount of water in the prescribed mix proportions. 

Additional Guidance:

• Edges Shall be cut back to avoid feather edging and all surfaces including edges shall be primed using Nitobond AR Std. bonding aid.
• All applications shall be wet on wet. For best results Nitobond AR Std. bonding aid should be allowed to become tacky. If the bonding agent is allowed to dry for more than 15 minutes at 300 C initial 'grab' to the repair mortar will be reduced. Therefore, the use of temporary shuttering is recommended. Water content of the mortar should be kept to the minimum necessary.
• For consistent results, the use of clean, dry sand is recommended.

Product Details:

We are one of the most reliable companies in this domain and are into offering High Performance Epoxy Mortar.

Other Details:-

• A two-part, high-strength epoxy adhesive and grout for interior and exterior use, available in a range of colours.
• grouting tiles where chemical resistance and/or complete impermeability are required: hospitals, laboratories, laundries, kitchens, dairies, abattoirs, breweries, distilleries, refrigerated rooms, toilets, bathrooms, swimming pools, car wash bays etc.
• fixing tiles where very high bond strength, toughness and flexibility are required

Benefits:

• Resistant to chemicals
• Impermeable to liquids and easy to sterilise, clean and maintain
• Flexible
• High bond strength
• Long working time
• Easy to use

 

Features

• Cost effective
• Longer shelf life
• Effectiveness
• Easy to apply
• Various forms available

Product Details:

Following industrial quality guidelines and standards, the provided range of Concrete Superplasticizer is formulated at vendors’ end by the use of highest quality chemical compounds and latest techniques.

Product Details:

• Accurate composition
• Longer shelf life
• Easy to use
• Hygienically made
• Safe packaging
• Reasonable rate

Uses:

• Auramix 350 is a high performance super plasticizer suitable for low and high grade concrete and intended for applications where high water reduction and long workability retentions are required. 
• Auramix 350 developed to use in:
• Long workability retention concrete.
• Pumpable Concrete.
• High performance concrete 

Advantages:

• Low viscosity admixture suitable for pumping different grades of concrete to greater heights.
• Suitable for concrete having cement replacements and low water cement ratio.
• Provides higher strength without increase in cement content or reduction in workability. Ideal for precast concrete production.
• Reduce rate of workability loss normally associated with super plasticiser. Reduces shrinkage cracking because of lower water cement ratio. Makes the concrete water impermeable.
• Better resistance to Carbonation.
• Reduce Shrinkage and Creep.
• Increase Durability.

Standard Compliance:

• Auramix 350 Complies with IS 9103-1999(2007) . It also complies with ASTM C 494 Type F & Type G depending on the dosage used. Description Auramix 350 is a unique combination of new generation Super Plasticizing admixture – Retarding type based on polycarboxilic ether polymer with long lateral chain. Electrostatic dispersion mechanism considerably reduces the water demand in flowable concrete. It is supplied as a light brown liquid, instantly dispersible in water.
• Auramix 350 disperses the cement particles effectively in the concrete mix and hence exposes a larger surface area to the hydration process. This effect is used either to increase the strength or to produce high workability concrete or reduce cement content of concrete or to retard the setting time of concrete.

Technical support:

• Fosroc provides technical advisory service for on-site assistance and guidance on mix design, optimum dosage evaluation of trials.

 

Dosage:

•  The optimum dosage of Auramix 350 to meet specific requirement should always be determined by conducting laboratory and batch trials. However the normal dosage ranges between 0.3 to 2.0 precent by weight of total cement or binder content.
• Dosage beyond Limits: Dosage beyond limits can be used to meet particular mix requirements in consultation with Fosroc technical department.
• Effect of over dosage: Over dosage may cause delay in setting and segregation.

Packaging:

• Auramix 350 is available in 200kg, 250kg drums and bulk tankers.

Storage:

• Auramix 350 has a minimum shelf life of 12 months provided the temperature is kept within range of 40 C and 500 C. 

Precautions:

• Health and safety instructions: Auramix 350 does not fall into the hazard classifications of current regulations. However, it should not be swallowed or allowed to come into contact with skin and eyes.
• Suitable protective gloves and goggles should be worn.
• Splashes on the skin should be removed with water. In case of contact with eyes rinse immediately with plenty of water and seek medical advice. If swallowed seek medical attention immediately - do not induce vomiting. 

Product Details:

Assisted by a crew of diligent and assiduous professionals, we have been able to provide an optimum quality array of Polymer Enhanced Grey Adhesive within the specified period of time.

 

Product Details:

• Precisely formulated
• Airtight packing
• Easy usage
• High effectiveness
• Non-toxic nature
• Accurate pH value

Product Details:

Yellow bay marking is designed to communicate restrictions on parking, waiting, and loading. Today, many road markings are not actually made of paint, but are instead thermoplastic which is applied while hot.

Product Details:

Tile adhesive is a special type of glue used to fix tiles all around the home. Tile adhesive is a ready-made mixture made from Portland cement, polymers such as epoxy and selected aggregate particles with some additives added in it to improve its property for laying tiles.

Product Details:

We are one of the most well-distinguished companies in the market that are into offering Latapoxy SP 100.

Product Details:

Yellow bay marking is designed to communicate restrictions on parking, waiting, and loading. Today, many road markings are not actually made of paint, but are instead thermoplastic which is applied while hot.

UGAM industrial bay marking paint is fast drying, p u acrylic composite road marking paint. 

These Paints have excellent light reflectance and tough coating as these are based on acrylic latex. Our hot melt type coatings are available in powder form. These are heated in machine and applied on the surface spray and then the glass beads are spread over before cooling.

4) These coatings are also called retro-reflective coatings.

The technical specification is correct to the best of our knowledge and under test conditions and we do not accept any liability towards misuse and contents of it. Product must be tested for specific use prior to use.

Product Details:

Enriched by our vast industrial experience in this business, we are involved in offering an enormous quality range of SBR Latex Nitobond Bonding Aid


Uses:

• For modifying and improving bonding of floor toppings, renderings and mortars; repair of worn, damaged and spalled concrete, repair of large cracks; polymer modified floor screeds; waterproof plasters for masonary and slurries.

Advantages:

• Simple to use: Single component, gauged as required.
• High: Provides excellent bond to concrete, adhesion plaster, masonry, stone work, etc.
• Improves: Gives weather resistant mortar with improved durability impermeability to chlorides and other harmful agents.
• Reduces: Provides waterproof screeds, plasters and Permeability slurries.
• Increases: Improved tensile and flexural properties strength allow thin applications.
• Versatile: Compatible with all common hydraulic cements.
• Cost effective: Nitobond SBR (Latex) is economical to use 

Description:

• Nitobond SBR(Latex) is modified styrene butadiene emulsion specially designed for use as a bonding aid and gauging liquid for cementitious systems. It is resistant to hydrolysis and can therefore be used for external applications too. 

Technical Support:

• Fosroc provides a technical advisory service supported by a team of specialists in the field.

Properties:

• Typical mechanical properties of 1 : 3 cement sand mortar at W/C - 0.45 for control and W/C - 0.35 for mortar containing Nitobond SBR (Latex) ( 5 lites / 50 kg cement ). Tested in accordance with BS 6319 & wet cured.

Chemical resistance:

• Cementitious based materials have limited chemical resitance. The addition of Nitobond SBR (Latex) to cement mortars reduces permeability and therefore helps reduce the rate of attack by aggressive chemicals. 

Application Instructions:

• Surface Preparation: The object of the surface preparation is to achieve a clean sound surface with a good mechanical key. All substrates should be cleaned and free of dust, plaster, oil, paint, grease, corrosion deposits, and any other deleterious substances. Laitence should be removed by mechanical means. Smooth substrates must be mechanically roughened e.g. by scabbling, needle gun or grit blasting to provide an adequate key.
• Corroded reinforcing steel should be exposed around its full circumference and cleaned to remove all loose scale and corrosion deposits. It is always preferably to clean the steel to a bright condition. Use of emery cloth, grit or sand blasting is recommended.

Priming:

• Reinforcing steel must be primed with Nitozinc Primer immediately after cleaning. The concrete substrate should be thoroughly dampened with water and any excess removed before being primed by thoroughly scrubbing in a slurry coat of 1 volume Nitbond SBR (Latex) to 1 volume water to 3 volumes fresh cement.
• In order to obtain a smooth consistency the cement should be blended slowly into the liquids. Stir frequently during use to offset settlement.

Packaging:

• Nitobond SBR (Latex) is supplied in 1, 5 and 20 litre containers.

Coverage:

• Slurry primer: approximately 4- 5 m2 / litre depending on substrate porosity. 

Storage:

• Shelf life: Nitobond SBR (Latex) has a shelf life of 12 months if kept in a dry store in unopened condition. 

Product Details:

In order to keep pace with the never-ending demands of customers, we are involved in offering a wide range of AR STD Nitobond Acrylic Bonding Agent

Uses:

• For improving and bonding floor toppings, mortars and renders
• As a bonding agent for Renderoc and other cementitious mortars
• Polymer modified mortars and screeds for reinstatement of worn out/damaged concrete
• Polymer modified concrete for improving the impermeability and there by enhancing the waterproofing property

Advantages:

• Good Adhesion: Provides good bond to concrete, masonry, stone work, plaster and block work.
• Increased Strength: Improves tensile and flexural properties of mortar.
• Versatile: Compatible with all common hydraulic cements
• User Friendly: application by brush/spray
• Improves Cohesion: No bleeding and segregation.

Description:

• Nitobond AR Std. is a single component latex acyrlic polymer emulsion used as bonding aid cum cement modifier with waterproofing property. 

Technical Support:

• Fosroc offers technical support service to specifiers, end users and contractors, as well as on-site technical assistance in locations all over the country

Mix proportions:

• As a cement modifier: 1 litre Nitobond AR Std. : 5 kg cement : 15 kgs graded quartz sand.
• As a bonding agent: 0.5 part cement : 1 part Nitobond AR Std. by weight.
• As waterproofing agent: 2-5% of Nitobond AR Std. shall be mixed with concrete by weight of cement. 

Application instructions:

• Surface Preparation: The object of the surface preparation is to achieve a clean sound surface with a good mechanical key. All substrates should be cleaned and free of dust, plaster, oil, paint, grease, corrosion deposits, and any other deleterious substances. Laitence should be removed by mechanical means. Oil or greasy deposits should be removed by suitable means. All surfaces so treated should be thoroughly washed with clean water. Smooth substrates must be mechanically roughened e.g. by scabbling, needle gun or grit/ sand blasting to provide a mechanical key.
• Concrete repairs: Any reinforcing steel in the repair area should be exposed around its full circumference and cleaned to remove all loose scale and corrosion deposits and then primed with Nitocote AP35, acrylic primer. All surface dust and debris shall be removed.
• Priming: Immediately before priming, the concrete substrate should be thoroughly dampened with water and any excess being brushed off. Scrub Nitobond AR Std. bonding aid into the substrate. Puddling of the emulsion to be avoided. The repair mortar/topping should be applied whilst the primer is still tacky. However a satisfactory bond can be achieved upto 15 mins. after application at 300 C.
• In order to obtain a smooth consistency mortar, the cement and sand must be dry mixed and then poured into the liquid with the required amount of water in the prescribed mix proportions. 

Additional Guidance:

• Edges Shall be cut back to avoid feather edging and all surfaces including edges shall be primed using Nitobond AR Std. bonding aid.
• All applications shall be wet on wet. For best results Nitobond AR Std. bonding aid should be allowed to become tacky. If the bonding agent is allowed to dry for more than 15 minutes at 300 C initial 'grab' to the repair mortar will be reduced. Therefore, the use of temporary shuttering is recommended. Water content of the mortar should be kept to the minimum necessary.
• For consistent results, the use of clean, dry sand is recommended.

Product Details:

Being a well-distinguished company in the market, we are into offering Concrete Admixture.

 

Product Details:

Backed by rich industrial experience we are offering waterproofing coating  to our customers providing the best services to our customers at reasonable rates